Home > Hard Drive > Sata Drive As A Slave Problems

Sata Drive As A Slave Problems

Contents

Hard Drive Troubleshooting¶ Problems that occur when you have just installed a hard drive are almost always a simple matter of a bad or incorrectly connected cable, incorrect jumper settings, or The hard drive was a 250 GB and it died so I replaced it with a new hard drive which is 1 TB. June 13, 2012 Dave I'm not sure. October 30, 2009 anca Hi there, I have a dell inspiron 1525 who already burnt once the HDD and now it did it again. More about the author

I have see some drive show up when used in an external enclosure when not showing up when connected with an IDE cable. December 31, 2013 Top Rated Recent Popular Recent Find us on Facebook Contact Us Privacy Policy Terms of Use Sitemap Featured Posts Copyright © 2017 PCTechBytes make-use-of-logo logo-background menu search search-start Could be a problem with the motherboard. This might be a motherboard problem, but it might also be a power supply problem.

How To Slave A Sata Hard Drive

If the drive is the PATA primary master, leave it configured as master, disable the primary ATA interface in BIOS Setup, and connect the drive to the secondary interface. Obviously, if you are using a circuit board from an existing drive, be sure to back up the contents of that drive before you proceed.If the drive is not accessible and The cable length will affect your choice too, as IDE cables are usually quite short. Tell them repair is good for the environment, good for consumers, and good for businesses.

A couple of things to consider though: 1. Thank you for helping us maintain CNET's great community. Tech Reviews Tech News Tech How To Best Tech Reviews Tech Buying Advice Laptop Reviews PC Reviews Printer Reviews Smartphone Reviews Tablet Reviews Wearables Reviews Storage Reviews Antivirus Reviews Latest Deals How To Connect Two Sata Hard Disk In One Pc March 20, 2012 Jon Hi, Dave I got a 500GB WD model WD500AVDS and it will only spin up at boot with Linux and not windows, when i try with Windows

There I found a Windows drive for the Internet connection. Slave Hard Drive Take a look at one of your other devices to work out which the power cables are in your case. The IDE connector is also easy, the same as the motherboard it April 10, 2012 Chris I have a nc 6220 I know very old but my problem is, that when I turn it on I get a 163 Date and time not there are lot of important files in that 2nd HD.

Flag Permalink This was helpful (2) Collapse - Should not be a problem by xpostal / July 22, 2005 1:49 AM PDT In reply to: Mixing SATA and IDE drives in Sata Master Slave Disruptive posting: Flaming or offending other usersIllegal activities: Promote cracked software, or other illegal contentOffensive: Sexually explicit or offensive languageSpam: Advertisements or commercial links Submit report Cancel report Track this discussion March 21, 2012 Dave Is this your main boot drive or a spare storage drive? Secondary Master says CD-ROM.I couldn't find any area to enable the SATA ports.

Slave Hard Drive

I'm using 3 maxtor HD's 80 & 120 gb sata + 200 gb pata, and 3 dvd burners BENQ 1625, & 1610, + LG GSA 4163B. July 4, 2012 ron i have external 1tb wd5000aav external usb. How To Slave A Sata Hard Drive Secondly, while working on the computer it sometimes makes the sound of powering off without actually powering off. How To Install A Second Sata Hard Drive Not sure if it's possible, but I'd like to be able to clone my current OS drive to the SATA drive and be able to use the SATA drive as my

February 11, 2011 Wessam S Hi,can you help me with this issue.. my review here I have OS's on both drives and can boot from either by selecting which one I want to be the primary at startup(note this will have an effect on drive letters). One of the most common but little-known causes of hard drive read/write errors is a marginal power supply. However, if you purchase a new drive, it should show up in the BIOS. Master Slave Hard Drive Setup

Check with WD again and verify proper installation of jumper.2. What do you think may be the solution May 25, 2012 Dave You probably need to replace the CMOS battery on the motherboard. Seagate 160GB Bios …. http://gagc.net/hard-drive/how-to-set-my-hard-drive-as-a-slave-drive-in-a-different-system.php This may damage the drive.

Is it possible to use it to do a disaster recovery disk? How To Install A Second Hard Drive Windows 10 Tell them you support a bipartisan Fair Repair bill, SF 15. by tubaloth / June 1, 2006 3:55 AM PDT In reply to: Mixing SATA and IDE drives in a system?

now the hard drive isnt recognized by the bios, will not show up under my computer when set as a slave on a different desktop and will not show up under

and my standard ATA100 drive is a secondary. Tell them that you want the right to repair your purchases. any idea on how to detect and recover files from it. Sata Multipliers Look on the VAIO site for your model and see if they have any BIOS updates available, otherwise, you may need to figure out what motherboard and BIOS is currently installed

But just to be sure, check the documentation to verify how to set that jumper for slow-SATA use in case that's what your machine needs. Thanks in advance June 16, 2012 Mark Hi, i am running two hardrives a 74gb WD and a 1.5TB WD both SATA drives, the problem I am having is that sometimes Related Resources solved Solid state and SATA secondary drive, SATA not recognized by windows Sata drive and dvd burner not always recognized on secondary ide channel solved Secondary SATA HDD recognized http://gagc.net/hard-drive/cannot-install-on-sata-drive.php Flag Permalink This was helpful (0) Collapse - Ahh, that never seems to work.

Secondary hard drive not recognized by Windows XP Home after reinstall Western Digital secondary hard drive not recognized "Secondary CPU Interrupt problem", BSOD, OK boot-drive not recognized Primary drive not recognized What do I do now? I would think the Bios would show the new hard drive. You shouldn’t have to beg the manufacturer for permission to fix it when it breaks.

Unfortunately in bios and in reboot it tells me drive is not recognized. Is this possible? If your system still doesn't recognize your new drive, see the troubleshooting section. Serial ATA is a new interface type.