Pass?/Fail? I've got a Dell Laptop with three hard drives which I swap out depending on the work I'm doing. Step 6: Identify If You Have A SATA Or IDE Drive Look at the following picture and compare it to your drive. Utterly Lost August 23, 2007 11:50 pm Reply # OK, I was running a custom built machine, kinda my first step into the world of technology at it's best. weblink
If you were running another OS use: Recover It All ayoola September 24, 2007 10:17 am Reply # I need tutorial on computer networking and slaving of hard disk and the Pye May 24, 2007 2:53 am Reply # Yes, the file system is a FAT 32. If not, you can also buy an SATA or ATX power splitter, turning one of your existing cables into two. How can I get the computer to recognise the keyboard at this prompt?
Tools needed: Phillips head screwdriver and a marker. show me de msg "..data corrupted or elegible" , i think is the partition. Does the laptop need to be taken apart or can this be done in a cable connection? Dave June 19, 2008 10:36 am Reply # What are the results of the test outlined above?
the properties tab, says that everthing is working properly, Very weird. The way you can get to disk management is by right clickong on my computer and going to MANAGE. Press "F10" to quit setup and boot from the alternate drive. How To Install A Second Sata Hard Drive In Windows 7 It is likely the drive has some kind of physical damage..
You can then get your files off or run data recovery software on the old drive to get your data back. What Is A Slave Hard Drive I hope this helps Jacqui Best August 18, 2008 5:22 pm Reply # teachingazteca: I would love to help with a reason why WIN98SE is not seeing the drive but the My external drive is formatted as Fat 32 and has SATA connectors. how can I use another external drive t make them master and slave mode boot it using More resources Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway
After you have unplugged it, take a marker and put a mark on it, this will help you to know which one to use when you put the drive back later. How To Slave A Hard Drive To Recover Data If so, how? i'll read the post while i wait for jacqui's reply. Make sure the power is plugged in and everything is connected securely.
If they aren't then you've got some troubleshooting to do. Do not apply pressure or attach labels to the circuit board or the top cover of the drive. How To Slave A Hard Drive Windows 7 the Global Study Desk nadun flower Reply Priyankar November 22, 2016 at 4:07 am I did the same procedure, what you have written but can't find the 2hdd option in" my Master Slave Hard Drive Setup Reply MikeTek July 10, 2016 at 6:36 pm Actually, slave is the middle connector and master is the end.
Today's machines derail people as they set the drive to SLAVE and new spiffy machines actually need the drive set to CABLE SELECT and then plugged into the SLAVE CONNECTOR.It's the http://gagc.net/hard-drive/how-to-move-operating-system-to-a-new-hard-drive.php by Eduardo A. grandpaw Flag Permalink This was helpful (0) Collapse - Re: Thanks, datalookup by Lawrence / August 29, 2004 10:36 PM PDT In reply to: Thanks, datalookup I don't know how old BUY NOW FREE TRIAL PARTITION MANAGER For Business » Partition Master ProfessionalBuyTry Partition Master ServerBuyTry Partition Master UnlimitedBuyTry For Home & Home Office » Partition Master FreeDownload Partition Master ProfessionalBuyTry For Master Slave Hard Drive Jumper Settings
Reply James Bruce January 22, 2011 at 12:07 pm Thanks Brad, thats what I was aiming for. DTI Data Recovery September 29, 2008 9:30 am Reply # Dan, You are going to have to remove the hard drive from the laptop. I would personally recommending using your extra drive to store the same as I do if you need to. http://gagc.net/hard-drive/sata-drive-as-a-slave-problems.php just like you would a camera card or a thumb drive.
Step 1: Identify If You Can Add Another Internal Drive Or Not Not all computers are built equal, unfortunately. How To Slave A Laptop Hard Drive After the drive is secured then go ahead and connect the power and IDE cables. Yes, you can use your old HDD in the new computer as a slave.
i cannot get the image recovery to work as i says "no image can be found on hard disk". Anyhow, I will get the pleasure of putting the old one in needy hands, kids I have been working with a long time. Once this is done buy the wire thing that connects my old one to the new one. Sata Hard Drive Slave Jumper Setting How to transfer Windows 7 from one hard drive to another.
Internal cables are ATA/IDE. Drive is Slave - Use this setting if the drive is an additional drive on the cable and the original drive is set as Master. can you tell me what can i do, for recover all of files? (+/- 90gb) sorry my english many thank you val eric August 28, 2007 8:59 pm Reply # i this content My new computer runs Windows Vista…Is it still possible to slave my older drive?
I’ll be covering the software and configuration side of adding a second drive in my next article – so stay tuned for that. Reply Ardiana December 31, 2016 at 3:27 pm IDE cables normally have 3 outlets, one for motherboard and two for hard drives/ CD drives. Volume label is nothing other than the name you want it to be called. Now my issue is how to retrieve the important files from the old hard drive.
I would have not been able to do this if you had not helped me diagnose the problem. Jacqui Best July 3, 2008 1:32 pm Reply # Peter, After further research I do not feel safe having you use one of the programs that allow Windows 98 to read Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. Also, the slot is keyed (aka fits only 1 way), so do not force the cable.
Flag Permalink This was helpful (0) Collapse - Re: Install old hard drive as slave drive? If the BIOS doesn't see the drive that means either the drive isn't connected and jumpered properly or is in such bad shape that it isn't seen by the BIOS. Comments How to slave a SATA drive The great thing about PCs is that they're easy to upgrade. Please Help!!
But it's a very good way to keep all your data, although you might want to reorganize it, and put everything (old and new) in a logical place. Share Tweet How to slave a SATA drive PC Advisor Phones Smartphone reviews Best smartphones Smartphone tips Smartphone buying advice Smartphone deals Laptops Laptops reviews Laptops tips Best laptops Laptops buying With modern SATA, which is a serial bus instead of the older parallel EIDE bus, things are simpler. Flag Permalink This was helpful (0) Collapse - Re: Install old hard drive as slave drive?
Windows 7 Help Forums Windows 7 help and support General Discussion » User Name Remember Me? Anyhow, the L'Oreal people tell me that I'm worth it, though I think they mean egotistically rather than economically. Can you tell if the slave drive is seen in the BIOS? Likewise, bus speed should be taken into consideration when buying a new RAM.