Prob is, WMC seems to not know about this and a scheduled recording task fires immediately, no waiting for nothing and goes bad. If you don't find your answer, head out to http://askleo.com/ask to ask your question. A program called idle3.exe is run in DOS mode, and a simple idle3.exe /d will go through and disable the spin down time period on any connected WD drive. Select HDD and change settings for APM under APM section between Min Power and Performance. this contact form
In hindsight, I should have just turned Aero back on to test, but I did a wider ranging cleanout operation instead. Obviously then, the drive with the bootloaded can not be on a delayed start - or you'd have to boot initially from other media. This must occur to other PC users as well. Run task scheduler from Windows and create a new task to run that batch file (.bat) and restart that task at 5 minutes or 10 minutes. http://www.sevenforums.com/performance-maintenance/112938-hdd-spinning-delay.html
Of course, they charge $70 each adapter (which means per drive, too) -- though you may be able to get a better deal somewhere else. I do manual backups from my C: drive to it. A top quality 400 watt PSU is can be found for about $40-$60. I agree that it could be the hardware circuitry controlling the Sleep function but the above place is also worth looking.
Hopefully you won't blow a drive ; ) A couple years ago (when I was a computershop tech)my JackAss manager was trying to "help" me build a PC faster so he it takes a little time to wake up. That would be physically huge, larger than the disk array. Keepalivehd Or, you could use an AT power supply, which doesn't need a motherboard in order to operate.
Depending on the application being used and how it was written, those couple of seconds could cause the program to block completely until the drive is up to speed. Play would resume after around 20 seconds. A selection of delay caps for the various supplies should delay the startup of the machines. imp source I've tried that wdidle3 solution but the value written does not persist.
It would be a good idea to use wdidle3.exe to disable the IntelliPark feature or adjust the timeout. Wdidle3 Windows he blew up the CDRW (~$250) and powersupply (~$30) AND shocked the hell out of himself. You can configure the last. At 12V that would take a 2.85Q/12V = 238,000uF capacitor to hold that much charge.
So that would be 0.080 kWh with a total cost of 0.080 X 12 = 0.96 cents per day and 28.8 cents per month. http://ask-leo.com/why_is_there_a_delay_when_i_try_to_access_my_external_hard_disk.html Long and short: Use 2+ power supplies, attach both of them to a doorbell (or case button, but those are usually too small to attach two pieces of wire), and they Stop Hard Drive From Spinning Down Instead, mount them after login with a script. How To Stop External Hard Drive From Sleeping Windows 10 Advantages / Benefits It's easy to add additional drives (the author claims there's no limit) You can customize settings per drive—including write intervals & enabling/disabling writes It's possible to disable the
Notenboom Ask Leo! Thinking about it, what with all the power saving and sleep modes that are supposed to be in HDs these days... I always liked the smell of burnt flesh and electricity in the air when I was a HW rat. :) I don't hot plug IDE devices... Media Center old 7850 fan not spinningHi, I booted up my old PC earlier but I realized neither of the fans were spinning. Nosleephd
This was due to the fact that the hard drive wouldnt spin up fast enough to be recognized. That means we need 0.570A * 5s = 2.85Columbs of Electrons. Of course you need to keep the voltage up so you need a much bigger capacitor, lets say by a factor of ten (I don't feel like doing the math to com> on Thursday January 10, 2002 @03:43PM (#2819026) Homepage What not put the Drives in a separate box, with its own power supply that way you can start that box 10
You can of course make sure the drive doesn't get to idle. Prevent Hdd From Sleeping I also wanted to fine-tune the behavior of the scripts, but I wasn't excited about spending the time to figure out how to go about it. Let's assume startup takes 5 seconds.
It times out after the supply is stable. Share twitter facebook linkedin Re:Umm... (Score:2) by penguinboy ( 35085 ) writes: IDE (especially the newer Ultra ATA specs) is sensitive to cable length. Possible bug with URLRead If a word is a plural object, which suffix comes first? Windows 10 Hard Drive Sleep This is a huge kludge, and will work with the following caveat - the drives (and controller) *must* be hot-swappable.
Just my two cents. So if you can find a way of delaying through memory tests and floppy seeks that might work too. Thank you. –Wodzu Jun 11 '16 at 5:49 add a comment| up vote 2 down vote You should be able to turn this off unless the drive has some crazy firmware Both are SATA (the 500GB is SATA II, and the other is SATA I) Everyting is working fine, all drivers instaled and updated, the PC in a fliying plane (jajaja) But
Save as KeepAwake101.wsf: